Hanging hardware, requiring a power cycle

Guff666 · 2021-01-15T16:55:05.381Z

I am running emonHub on a Pi3 with the RFM69 board connected to the GPIO. It’s been running with no problems for some time now, but I woke up this morning to find that emonHub was not transmitting any sensor updates. Visual inspection revealed that the red LED was lit on the RF card.

A full power cycle was required to recover. Any ideas on how to debug this? As a precaution I have enabled persistent journals, in case it happens again.

borpin · 2021-01-16T10:57:48.361Z

There is another thread about emonhub stopping (died) Emonhub died. Check the emonhub logs.

Are you running just emonhub (i.e. not the EmonSD)?

Guff666 · 2021-01-17T14:41:21.114Z

Thanks for the pointer.
emonHub is running on a Pi that is also running Docker for some other stuff, including a local MQTT server.
I’ve looked back at the logs produced around the time the updates stopped. The last successful packet is at 02:03:49. There’s no further log entries until I restart emonHub at 15:44. This has no effect, so I reboot at 15:48. Again, no effect so I power cycle and the log resumes at 15:51 and we start getting packets again. There is a brief hiatus as we wait for the mqtt server to become available but then all is well.

Here’s the filtered log

Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    RFM2Pi     26090 NEW FRAME : OK 26 162 0 0 0 159 1 27 0 1 0 0 0 (-50)
Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    RFM2Pi     26090 Timestamp : 1610676228.496683
Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    RFM2Pi     26090 From Node : 26
Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    RFM2Pi     26090    Values : [16.2, 0, 41.5, 2.7, 1]
Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    RFM2Pi     26090      RSSI : -50
Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    RFM2Pi     26090 Sent to channel(start)' : ToEmonCMS
Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    RFM2Pi     26090 Sent to channel(end)' : ToEmonCMS
Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emon/emonth8/temperature 16.2
Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emon/emonth8/external temperature 0
Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emon/emonth8/humidity 41.5
Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emon/emonth8/battery 2.7
Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emon/emonth8/pulsecount 1
Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emon/emonth8/rssi -50
Jan 15 02:03:48 docker4 emonHub[536]: INFO     MQTT       Publishing 'node' formatted msg
Jan 15 02:03:48 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emonhub/rx/26/values 16.2,0,41.5,2.7,1,-50
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    RFM2Pi     26091 NEW FRAME : OK 25 188 0 0 0 186 1 28 0 1 0 0 0 (-37)
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    RFM2Pi     26091 Timestamp : 1610676229.306698
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    RFM2Pi     26091 From Node : 25
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    RFM2Pi     26091    Values : [18.8, 0, 44.2, 2.8000000000000003, 1]
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    RFM2Pi     26091      RSSI : -37
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    RFM2Pi     26091 Sent to channel(start)' : ToEmonCMS
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    RFM2Pi     26091 Sent to channel(end)' : ToEmonCMS
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emon/emonth7/temperature 18.8
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emon/emonth7/external temperature 0
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emon/emonth7/humidity 44.2
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emon/emonth7/battery 2.8000000000000003
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emon/emonth7/pulsecount 1
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emon/emonth7/rssi -37
Jan 15 02:03:49 docker4 emonHub[536]: INFO     MQTT       Publishing 'node' formatted msg
Jan 15 02:03:49 docker4 emonHub[536]: DEBUG    MQTT       Publishing: emonhub/rx/25/values 18.8,0,44.2,2.8000000000000003,1,-37
Jan 15 02:04:12 docker4 emonHub[536]: DEBUG    emoncmsorg Buffer size: 2
Jan 15 15:44:53 docker4 systemd[1]: Stopping emonHub data multiplexer...
Jan 15 15:44:53 docker4 emonHub[536]: DEBUG    MainThread Signal 15 received.
Jan 15 15:44:53 docker4 emonHub[536]: INFO     MainThread Exiting hub...
Jan 15 15:44:53 docker4 emonHub[536]: INFO     MainThread Exit completed
Jan 15 15:44:54 docker4 systemd[1]: Stopped emonHub data multiplexer.
Jan 15 15:44:54 docker4 systemd[1]: Starting emonHub data multiplexer...
Jan 15 15:44:54 docker4 systemd[1]: Started emonHub data multiplexer.
Jan 15 15:44:56 docker4 emonHub[15767]: INFO     MainThread EmonHub emonHub (emon-pi variant) v2.1.5
Jan 15 15:44:56 docker4 emonHub[15767]: INFO     MainThread Opening hub...
Jan 15 15:44:56 docker4 emonHub[15767]: INFO     MainThread Logging level set to DEBUG
Jan 15 15:44:56 docker4 emonHub[15767]: INFO     MainThread Creating EmonHubJeeInterfacer 'RFM2Pi'
Jan 15 15:44:56 docker4 emonHub[15767]: DEBUG    MainThread Opening serial port: /dev/ttyAMA0 @ 38400 bits/s
Jan 15 15:44:58 docker4 emonHub[15767]: INFO     MainThread RFM2Pi device firmware version: [RF12demo.13]
Jan 15 15:44:58 docker4 emonHub[15767]: INFO     MainThread RFM2Pi device current settings:  E i5 g210 @ 433 MHz q1
Jan 15 15:44:58 docker4 emonHub[15767]: INFO     MainThread Setting RFM2Pi calibration: 230V (1p)
Jan 15 15:44:59 docker4 emonHub[15767]: DEBUG    MainThread Setting RFM2Pi pubchannels: ['ToEmonCMS']
Jan 15 15:44:59 docker4 emonHub[15767]: DEBUG    MainThread Setting RFM2Pi subchannels: ['ToRFM12']
Jan 15 15:44:59 docker4 emonHub[15767]: INFO     MainThread Creating EmonHubMqttInterfacer 'MQTT'
Jan 15 15:44:59 docker4 emonHub[15767]: DEBUG    RFM2Pi     acknowledged command: > 1p
Jan 15 15:44:59 docker4 emonHub[15767]: DEBUG    MainThread Setting MQTT pubchannels: ['ToRFM12']
Jan 15 15:44:59 docker4 emonHub[15767]: DEBUG    MainThread Setting MQTT subchannels: ['ToEmonCMS']
Jan 15 15:44:59 docker4 emonHub[15767]: INFO     MainThread Setting MQTT node_format_enable: 1
Jan 15 15:44:59 docker4 emonHub[15767]: INFO     MainThread Setting MQTT nodevar_format_enable: 1
Jan 15 15:44:59 docker4 emonHub[15767]: INFO     MainThread Setting MQTT nodevar_format_basetopic: emon/
Jan 15 15:44:59 docker4 emonHub[15767]: INFO     MainThread Setting MQTT node_JSON_enable: 0
Jan 15 15:44:59 docker4 emonHub[15767]: INFO     MainThread Creating EmonHubEmoncmsHTTPInterfacer 'emoncmsorg'
Jan 15 15:44:59 docker4 emonHub[15767]: DEBUG    MainThread Setting emoncmsorg pubchannels: ['ToRFM12']
Jan 15 15:44:59 docker4 emonHub[15767]: DEBUG    MainThread Setting emoncmsorg subchannels: ['ToEmonCMS']
Jan 15 15:44:59 docker4 emonHub[15767]: WARNING  MainThread Setting emoncmsorg apikey: obscured
Jan 15 15:44:59 docker4 emonHub[15767]: INFO     MainThread Setting emoncmsorg url: https://emoncms.org
Jan 15 15:44:59 docker4 emonHub[15767]: INFO     MainThread Setting emoncmsorg senddata: 1
Jan 15 15:44:59 docker4 emonHub[15767]: INFO     MainThread Setting emoncmsorg sendstatus: 1
Jan 15 15:44:59 docker4 emonHub[15767]: DEBUG    RFM2Pi     acknowledged command: <nn> i     - set node ID (standard node ids are 1..30)
Jan 15 15:44:59 docker4 emonHub[15767]: DEBUG    RFM2Pi     acknowledged command: <n> b      - set MHz band (4 = 433, 8 = 868, 9 = 915)
Jan 15 15:45:00 docker4 emonHub[15767]: DEBUG    RFM2Pi     acknowledged command: <nnnn> o   - change frequency offset within the band (default 1600)
Jan 15 15:45:00 docker4 emonHub[15767]: DEBUG    RFM2Pi     acknowledged command: <nnn> g    - set network group (RFM12 only allows 212, 0 = any)
Jan 15 15:45:00 docker4 emonHub[15767]: DEBUG    RFM2Pi     acknowledged command: <n> c      - set collect mode (advanced, normally 0)
Jan 15 15:45:00 docker4 emonHub[15767]: DEBUG    RFM2Pi     acknowledged command: ...,<nn> a - send data packet to node <nn>, request ack
Jan 15 15:45:00 docker4 emonHub[15767]: DEBUG    RFM2Pi     acknowledged command: ...,<nn> s - send data packet to node <nn>, no ack
Jan 15 15:45:00 docker4 emonHub[15767]: DEBUG    RFM2Pi     acknowledged command: <n> q      - set quiet mode (1 = don't report bad packets)
Jan 15 15:45:00 docker4 emonHub[15767]: DEBUG    RFM2Pi     acknowledged command: <n> x      - set reporting format (0: decimal, 1: hex, 2: hex+ascii)
Jan 15 15:45:01 docker4 emonHub[15767]: DEBUG    RFM2Pi     acknowledged command: <hchi>,<hclo>,<addr>,<cmd> f     - FS20 command (868 MHz)
Jan 15 15:45:01 docker4 emonHub[15767]: DEBUG    RFM2Pi     acknowledged command: <addr>,<dev>,<on> k              - KAKU command (433 MHz)
Jan 15 15:45:01 docker4 emonHub[15767]: DEBUG    RFM2Pi     device settings updated: E i5 g210 @ 433 MHz q1
Jan 15 15:48:19 docker4 systemd[1]: Starting emonHub data multiplexer...
Jan 15 15:48:19 docker4 systemd[1]: Started emonHub data multiplexer.
Jan 15 15:48:24 docker4 emonHub[538]: INFO     MainThread EmonHub emonHub (emon-pi variant) v2.1.5
Jan 15 15:48:24 docker4 emonHub[538]: INFO     MainThread Opening hub...
Jan 15 15:48:24 docker4 emonHub[538]: INFO     MainThread Logging level set to DEBUG
Jan 15 15:48:24 docker4 emonHub[538]: INFO     MainThread Creating EmonHubJeeInterfacer 'RFM2Pi'
Jan 15 15:48:24 docker4 emonHub[538]: DEBUG    MainThread Opening serial port: /dev/ttyAMA0 @ 38400 bits/s
Jan 15 15:48:26 docker4 emonHub[538]: INFO     MainThread RFM2Pi device firmware version: [RF12demo.13]
Jan 15 15:48:26 docker4 emonHub[538]: INFO     MainThread RFM2Pi device current settings:  E i5 g210 @ 433 MHz q1
Jan 15 15:48:26 docker4 emonHub[538]: INFO     MainThread Setting RFM2Pi calibration: 230V (1p)
Jan 15 15:48:27 docker4 emonHub[538]: DEBUG    MainThread Setting RFM2Pi pubchannels: ['ToEmonCMS']
Jan 15 15:48:27 docker4 emonHub[538]: DEBUG    MainThread Setting RFM2Pi subchannels: ['ToRFM12']
Jan 15 15:48:27 docker4 emonHub[538]: INFO     MainThread Creating EmonHubMqttInterfacer 'MQTT'
Jan 15 15:48:27 docker4 emonHub[538]: DEBUG    RFM2Pi     acknowledged command: > 1p
Jan 15 15:48:27 docker4 emonHub[538]: DEBUG    MainThread Setting MQTT pubchannels: ['ToRFM12']
Jan 15 15:48:27 docker4 emonHub[538]: DEBUG    MainThread Setting MQTT subchannels: ['ToEmonCMS']
Jan 15 15:48:27 docker4 emonHub[538]: INFO     MainThread Setting MQTT node_format_enable: 1
Jan 15 15:48:27 docker4 emonHub[538]: INFO     MainThread Setting MQTT nodevar_format_enable: 1
Jan 15 15:48:27 docker4 emonHub[538]: INFO     MainThread Setting MQTT nodevar_format_basetopic: emon/
Jan 15 15:48:27 docker4 emonHub[538]: INFO     MainThread Setting MQTT node_JSON_enable: 0
Jan 15 15:48:27 docker4 emonHub[538]: INFO     MainThread Creating EmonHubEmoncmsHTTPInterfacer 'emoncmsorg'
Jan 15 15:48:27 docker4 emonHub[538]: DEBUG    MainThread Setting emoncmsorg pubchannels: ['ToRFM12']
Jan 15 15:48:27 docker4 emonHub[538]: DEBUG    MainThread Setting emoncmsorg subchannels: ['ToEmonCMS']
Jan 15 15:48:27 docker4 emonHub[538]: WARNING  MainThread Setting emoncmsorg apikey: obscured
Jan 15 15:48:27 docker4 emonHub[538]: INFO     MainThread Setting emoncmsorg url: https://emoncms.org
Jan 15 15:48:27 docker4 emonHub[538]: INFO     MainThread Setting emoncmsorg senddata: 1
Jan 15 15:48:27 docker4 emonHub[538]: INFO     MainThread Setting emoncmsorg sendstatus: 1
Jan 15 15:48:27 docker4 emonHub[538]: DEBUG    RFM2Pi     acknowledged command: <nn> i     - set node ID (standard node ids are 1..30)
Jan 15 15:48:27 docker4 emonHub[538]: DEBUG    RFM2Pi     acknowledged command: <n> b      - set MHz band (4 = 433, 8 = 868, 9 = 915)
Jan 15 15:48:27 docker4 emonHub[538]: DEBUG    RFM2Pi     acknowledged command: <nnnn> o   - change frequency offset within the band (default 1600)
Jan 15 15:48:28 docker4 emonHub[538]: DEBUG    RFM2Pi     acknowledged command: <nnn> g    - set network group (RFM12 only allows 212, 0 = any)
Jan 15 15:48:28 docker4 emonHub[538]: DEBUG    RFM2Pi     acknowledged command: <n> c      - set collect mode (advanced, normally 0)
Jan 15 15:48:28 docker4 emonHub[538]: DEBUG    RFM2Pi     acknowledged command: ...,<nn> a - send data packet to node <nn>, request ack
Jan 15 15:48:28 docker4 emonHub[538]: DEBUG    RFM2Pi     acknowledged command: ...,<nn> s - send data packet to node <nn>, no ack
Jan 15 15:48:28 docker4 emonHub[538]: DEBUG    RFM2Pi     acknowledged command: <n> q      - set quiet mode (1 = don't report bad packets)
Jan 15 15:48:28 docker4 emonHub[538]: DEBUG    RFM2Pi     acknowledged command: <n> x      - set reporting format (0: decimal, 1: hex, 2: hex+ascii)
Jan 15 15:48:29 docker4 emonHub[538]: DEBUG    RFM2Pi     acknowledged command: <hchi>,<hclo>,<addr>,<cmd> f     - FS20 command (868 MHz)
Jan 15 15:48:29 docker4 emonHub[538]: DEBUG    RFM2Pi     acknowledged command: <addr>,<dev>,<on> k              - KAKU command (433 MHz)
Jan 15 15:48:29 docker4 emonHub[538]: DEBUG    RFM2Pi     device settings updated: E i5 g210 @ 433 MHz q1
Jan 15 15:51:41 docker4 systemd[1]: Starting emonHub data multiplexer...
Jan 15 15:51:41 docker4 systemd[1]: Started emonHub data multiplexer.
Jan 15 15:51:46 docker4 emonHub[544]: INFO     MainThread EmonHub emonHub (emon-pi variant) v2.1.5
Jan 15 15:51:46 docker4 emonHub[544]: INFO     MainThread Opening hub...
Jan 15 15:51:46 docker4 emonHub[544]: INFO     MainThread Logging level set to DEBUG
Jan 15 15:51:46 docker4 emonHub[544]: INFO     MainThread Creating EmonHubJeeInterfacer 'RFM2Pi'
Jan 15 15:51:46 docker4 emonHub[544]: DEBUG    MainThread Opening serial port: /dev/ttyAMA0 @ 38400 bits/s
Jan 15 15:51:48 docker4 emonHub[544]: INFO     MainThread RFM2Pi device firmware version: [RF12demo.13]
Jan 15 15:51:48 docker4 emonHub[544]: INFO     MainThread RFM2Pi device current settings:  E i5 g210 @ 433 MHz q1
Jan 15 15:51:48 docker4 emonHub[544]: INFO     MainThread Setting RFM2Pi calibration: 230V (1p)
Jan 15 15:51:49 docker4 emonHub[544]: DEBUG    MainThread Setting RFM2Pi pubchannels: ['ToEmonCMS']
Jan 15 15:51:49 docker4 emonHub[544]: DEBUG    MainThread Setting RFM2Pi subchannels: ['ToRFM12']
Jan 15 15:51:49 docker4 emonHub[544]: INFO     MainThread Creating EmonHubMqttInterfacer 'MQTT'
Jan 15 15:51:49 docker4 emonHub[544]: DEBUG    RFM2Pi     acknowledged command: > 1p
Jan 15 15:51:49 docker4 emonHub[544]: DEBUG    MainThread Setting MQTT pubchannels: ['ToRFM12']
Jan 15 15:51:49 docker4 emonHub[544]: DEBUG    MainThread Setting MQTT subchannels: ['ToEmonCMS']
Jan 15 15:51:49 docker4 emonHub[544]: INFO     MainThread Setting MQTT node_format_enable: 1
Jan 15 15:51:49 docker4 emonHub[544]: INFO     MainThread Setting MQTT nodevar_format_enable: 1
Jan 15 15:51:49 docker4 emonHub[544]: INFO     MainThread Setting MQTT nodevar_format_basetopic: emon/
Jan 15 15:51:49 docker4 emonHub[544]: INFO     MainThread Setting MQTT node_JSON_enable: 0
Jan 15 15:51:49 docker4 emonHub[544]: INFO     MainThread Creating EmonHubEmoncmsHTTPInterfacer 'emoncmsorg'
Jan 15 15:51:49 docker4 emonHub[544]: DEBUG    MainThread Setting emoncmsorg pubchannels: ['ToRFM12']
Jan 15 15:51:49 docker4 emonHub[544]: DEBUG    MainThread Setting emoncmsorg subchannels: ['ToEmonCMS']
Jan 15 15:51:49 docker4 emonHub[544]: WARNING  MainThread Setting emoncmsorg apikey: obscured
Jan 15 15:51:49 docker4 emonHub[544]: INFO     MainThread Setting emoncmsorg url: https://emoncms.org
Jan 15 15:51:49 docker4 emonHub[544]: INFO     MainThread Setting emoncmsorg senddata: 1
Jan 15 15:51:49 docker4 emonHub[544]: INFO     MainThread Setting emoncmsorg sendstatus: 1
Jan 15 15:51:50 docker4 emonHub[544]: DEBUG    RFM2Pi     acknowledged command: <nn> i     - set node ID (standard node ids are 1..30)
Jan 15 15:51:50 docker4 emonHub[544]: DEBUG    RFM2Pi     acknowledged command: <n> b      - set MHz band (4 = 433, 8 = 868, 9 = 915)
Jan 15 15:51:50 docker4 emonHub[544]: DEBUG    RFM2Pi     acknowledged command: <nnnn> o   - change frequency offset within the band (default 1600)
Jan 15 15:51:50 docker4 emonHub[544]: DEBUG    RFM2Pi     acknowledged command: <nnn> g    - set network group (RFM12 only allows 212, 0 = any)
Jan 15 15:51:50 docker4 emonHub[544]: DEBUG    RFM2Pi     acknowledged command: <n> c      - set collect mode (advanced, normally 0)
Jan 15 15:51:50 docker4 emonHub[544]: DEBUG    RFM2Pi     acknowledged command: ...,<nn> a - send data packet to node <nn>, request ack
Jan 15 15:51:50 docker4 emonHub[544]: DEBUG    RFM2Pi     acknowledged command: ...,<nn> s - send data packet to node <nn>, no ack
Jan 15 15:51:51 docker4 emonHub[544]: DEBUG    RFM2Pi     acknowledged command: <n> q      - set quiet mode (1 = don't report bad packets)
Jan 15 15:51:51 docker4 emonHub[544]: DEBUG    RFM2Pi     acknowledged command: <n> x      - set reporting format (0: decimal, 1: hex, 2: hex+ascii)
Jan 15 15:51:51 docker4 emonHub[544]: DEBUG    RFM2Pi     acknowledged command: <hchi>,<hclo>,<addr>,<cmd> f     - FS20 command (868 MHz)
Jan 15 15:51:51 docker4 emonHub[544]: DEBUG    RFM2Pi     acknowledged command: <addr>,<dev>,<on> k              - KAKU command (433 MHz)
Jan 15 15:51:51 docker4 emonHub[544]: DEBUG    RFM2Pi     device settings updated: E i5 g210 @ 433 MHz q1
Jan 15 15:51:58 docker4 emonHub[544]: DEBUG    RFM2Pi     7 NEW FRAME : OK 26 4 1 0 0 132 1 27 0 1 0 0 0 (-57)
Jan 15 15:51:58 docker4 emonHub[544]: DEBUG    RFM2Pi     7 Timestamp : 1610725918.448843
Jan 15 15:51:58 docker4 emonHub[544]: DEBUG    RFM2Pi     7 From Node : 26
Jan 15 15:51:58 docker4 emonHub[544]: DEBUG    RFM2Pi     7    Values : [26, 0, 38.800000000000004, 2.7, 1]
Jan 15 15:51:58 docker4 emonHub[544]: DEBUG    RFM2Pi     7      RSSI : -57
Jan 15 15:51:58 docker4 emonHub[544]: DEBUG    RFM2Pi     7 Sent to channel(start)' : ToEmonCMS
Jan 15 15:51:58 docker4 emonHub[544]: DEBUG    RFM2Pi     7 Sent to channel(end)' : ToEmonCMS
Jan 15 15:51:58 docker4 emonHub[544]: INFO     MQTT       Connecting to MQTT Server
...

Jan 15 15:53:08 docker4 emonHub[544]: INFO     MQTT       connection status: Connection successful
Jan 15 15:53:08 docker4 emonHub[544]: DEBUG    MQTT       CONACK => Return code: 0
Jan 15 15:53:15 docker4 emonHub[544]: INFO     MQTT       on_subscribe
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    RFM2Pi     12 NEW FRAME : OK 24 196 0 32 0 177 1 28 0 1 0 0 0 (-62)
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    RFM2Pi     12 Timestamp : 1610725997.525853
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    RFM2Pi     12 From Node : 24
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    RFM2Pi     12    Values : [19.6, 3.2, 43.300000000000004, 2.8000000000000003, 1]
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    RFM2Pi     12      RSSI : -62
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    RFM2Pi     12 Sent to channel(start)' : ToEmonCMS
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    RFM2Pi     12 Sent to channel(end)' : ToEmonCMS
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth6/temperature 19.6
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth6/external temperature 3.2
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth6/humidity 43.300000000000004
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth6/battery 2.8000000000000003
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth6/pulsecount 1
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth6/rssi -62
Jan 15 15:53:17 docker4 emonHub[544]: INFO     MQTT       Publishing 'node' formatted msg
Jan 15 15:53:17 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emonhub/rx/24/values 19.6,3.2,43.300000000000004,2.8000000000000003,1,-62
Jan 15 15:53:24 docker4 emonHub[544]: DEBUG    RFM2Pi     13 NEW FRAME : OK 25 200 0 0 0 189 1 28 0 1 0 0 0 (-37)
Jan 15 15:53:24 docker4 emonHub[544]: DEBUG    RFM2Pi     13 Timestamp : 1610726004.969542
Jan 15 15:53:24 docker4 emonHub[544]: DEBUG    RFM2Pi     13 From Node : 25
Jan 15 15:53:24 docker4 emonHub[544]: DEBUG    RFM2Pi     13    Values : [20, 0, 44.5, 2.8000000000000003, 1]
Jan 15 15:53:24 docker4 emonHub[544]: DEBUG    RFM2Pi     13      RSSI : -37
Jan 15 15:53:24 docker4 emonHub[544]: DEBUG    RFM2Pi     13 Sent to channel(start)' : ToEmonCMS
Jan 15 15:53:24 docker4 emonHub[544]: DEBUG    RFM2Pi     13 Sent to channel(end)' : ToEmonCMS
Jan 15 15:53:25 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth7/temperature 20
Jan 15 15:53:25 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth7/external temperature 0
Jan 15 15:53:25 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth7/humidity 44.5
Jan 15 15:53:25 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth7/battery 2.8000000000000003
Jan 15 15:53:25 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth7/pulsecount 1
Jan 15 15:53:25 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth7/rssi -37
Jan 15 15:53:25 docker4 emonHub[544]: INFO     MQTT       Publishing 'node' formatted msg
Jan 15 15:53:25 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emonhub/rx/25/values 20,0,44.5,2.8000000000000003,1,-37
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    RFM2Pi     14 NEW FRAME : OK 23 187 0 0 0 226 1 29 0 1 0 0 0 (-27)
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    RFM2Pi     14 Timestamp : 1610726006.299201
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    RFM2Pi     14 From Node : 23
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    RFM2Pi     14    Values : [18.7, 0, 48.2, 2.9000000000000004, 1]
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    RFM2Pi     14      RSSI : -27
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    RFM2Pi     14 Sent to channel(start)' : ToEmonCMS
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    RFM2Pi     14 Sent to channel(end)' : ToEmonCMS
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth5/temperature 18.7
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth5/external temperature 0
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth5/humidity 48.2
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth5/battery 2.9000000000000004
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth5/pulsecount 1
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emon/emonth5/rssi -27
Jan 15 15:53:26 docker4 emonHub[544]: INFO     MQTT       Publishing 'node' formatted msg
Jan 15 15:53:26 docker4 emonHub[544]: DEBUG    MQTT       Publishing: emonhub/rx/23/values 18.7,0,48.2,2.9000000000000004,1,-27
Jan 15 15:53:28 docker4 emonHub[544]: DEBUG    emoncmsorg Buffer size: 3

borpin · 2021-01-17T15:07:41.287Z

Sadly yes, this has been seen before but the reason remains unknown (and rare).

The most likely reason is Network issues.

Guff666 · 2021-01-17T15:14:43.244Z

OK, thanks, Brian.

Next time it happens, I’ll try the reset script mentioned in the other thread. If this is successful, I can build an auto-responder that kicks in when data stops flowing.