#include "labeldef.h"
//  This file is a definition file for the ESPAtherma.
//  uncomment each value you want to query for your installation.

LabelDef labelDefs[] = {
//{0x00,0,802,0,-1,"*Refrigerant type"},
//{0x00,0,152,1,-1,"Sensor Data Qty"},
//{0x00,1,152,1,-1,"INV compressor Qty"},
//{0x00,2,152,1,-1,"STD compressor Qty"},
//{0x00,3,152,1,-1,"Fan Data Qty"},
//{0x00,4,152,1,-1,"Expansion Valve Data Qty"},
//{0x00,5,152,1,-1,"4 Way Valve Data Qty"},
//{0x00,6,152,1,-1,"Crank Case Heater Qty"},
//{0x00,7,152,1,-1,"Solenoid valve Qty"},
//{0x00,8,152,1,-1,"Max. connectable indoor units"},
//{0x00,9,152,1,-1,"Connected Indoor Unit Qty"},
//{0x00,10,152,1,-1,"O/U MPU ID (xx)"},
//{0x00,11,152,1,-1,"O/U MPU ID (yy)"},
//{0x00,12,105,1,-1,"O/U capacity (kW)"},
{0x10,0,217,1,-1,"Operation Mode"},
{0x10,1,307,1,-1,"Thermostat ON/OFF"},
{0x10,1,306,1,-1,"Restart standby"},
{0x10,1,305,1,-1,"Startup Control"},
{0x10,1,304,1,-1,"Defrost Operation"},
//{0x10,1,303,1,-1,"Oil Return Operation"},
//{0x10,1,302,1,-1,"Pressure equalizing operation"},
//{0x10,1,301,1,-1,"Demand Signal"},
{0x10,1,300,1,-1,"Low noise control"},
//{0x10,4,203,1,-1,"Error type"},
//{0x10,5,204,1,-1,"Error Code"},
{0x10,6,114,2,1,"Target Evap. Temp."},
{0x10,8,114,2,1,"Target Cond. Temp."},
//{0x10,10,307,1,-1,"Discharge Temp. Drop"},
//{0x10,10,310,1,-1,"Discharge Temp. Protection Retry Qty"},
//{0x10,10,303,1,-1,"Comp. INV Current Drop"},
//{0x10,10,311,1,-1,"Comp. INV Current Protection Retry Qty"},
//{0x10,11,307,1,-1,"HP Drop Control"},
//{0x10,11,310,1,-1,"HP Protection Retry Qty"},
//{0x10,11,303,1,-1,"LP Drop Control"},
//{0x10,11,311,1,-1,"LP Protection Retry Qty"},
//{0x10,12,307,1,-1,"Fin Temp. Drop Control"},
//{0x10,12,310,1,-1,"Fin Temp. Protection Retry Qty"},
//{0x10,12,303,1,-1,"Other Drop Control"},
//{0x10,12,311,1,-1,"Not in use"},
//{0x11,0,215,1,-1,"O/U EEPROM (1st digit)"},
//{0x11,1,215,1,-1,"O/U EEPROM (3rd 4th digit)"},
//{0x11,2,215,1,-1,"O/U EEPROM (5th 6th digit)"},
//{0x11,3,215,1,-1,"O/U EEPROM (7th 8th digit)"},
//{0x11,4,215,1,-1,"O/U EEPROM (10th digit)"},
//{0x11,5,214,1,-1,"O/U EEPROM (11th digit)"},
//{0x00,0,995,1,-1,"NextDataGrid"},
{0x20,0,105,2,1,"Outdoor air temp.(R1T)"},
{0x20,2,105,2,1,"O/U Heat Exch. Temp.(R4T)"},
{0x20,4,105,2,1,"Discharge pipe temp.(R2T)"},
{0x20,6,105,2,1,"Suction pipe temp.(R3T)"},
{0x20,8,105,2,1,"Heat exchanger mid-temp.(R5T)"},
{0x20,10,105,2,1,"Liquid pipe temp.(R6T)"},
//{0x20,12,105,2,2,"High Pressure"},
//{0x20,12,405,2,1,"High Pressure(T)"},
//{0x20,14,105,2,2,"Low Pressure"},
//{0x20,14,405,2,1,"Low Pressure(T)"},
{0x21,0,105,2,-1,"INV primary current (A)"},
{0x21,2,105,2,-1,"INV secondary current (A)"},
{0x21,4,101,2,-1,"Voltage (N-phase) (V)"},
{0x21,4,105,2,1,"INV fin temp."},
{0x21,6,105,2,1,"Fan1 Fin temp."},
//{0x21,8,105,2,1,"Fan2 Fin temp."},
{0x21,10,105,2,1,"Compressor outlet temperature"},
//{0x00,0,995,1,-1,"NextDataGrid"},
{0x30,0,152,1,-1,"INV frequency (rps)"},
{0x30,1,211,1,-1,"Fan 1 (step)"},
{0x30,2,211,1,-1,"Fan 2 (step)"},
//{0x30,3,151,2,-1,"Expansion valve 1 (pls)"},
//{0x30,5,151,2,-1,"Expansion valve 2 (pls)"},
//{0x30,7,151,2,-1,"Expansion valve 3 (pls)"},
//{0x30,9,151,2,-1,"Expansion valve 4 (pls)"},
//{0x30,11,307,1,-1,"4 Way Valve"},
{0x30,12,307,1,-1,"Crank case heater"},
//{0x30,13,307,1,-1,"Hot gas bypass valve (Y3S)"},
//{0x30,13,306,1,-1,"LP bypass valve (Y2S)"},
//{0x30,13,305,1,-1,"Y3S"},
//{0x00,0,998,1,-1,"In-Out separator"},
{0xA0,0,119,2,1,"Suction temp"},
{0xA0,2,119,2,1,"Outdoor heat exchanger temp."},
{0xA0,4,119,2,1,"Liquid pipe temp."},
{0xA0,6,119,2,2,"Pressure"},
//{0xA0,8,151,2,-1,"Expansion valve 3 (pls)"},
//{0xA0,10,152,1,-1,"O/U MPU ID"},
//{0xA0,11,152,1,-1,"O/U MPU ID"},
//{0xA0,12,307,1,-1,"HPS operation"},
{0xA0,12,306,1,-1,"Safeguard operation"},
{0xA0,12,305,1,-1,"Crank case heater"},
//{0xA0,12,304,1,-1,"Solenoid Valve 3"},
//{0xA0,12,303,1,-1,"Solenoid Valve 2"},
//{0xA0,12,302,1,-1,"Solenoid Valve 1"},
//{0xA0,12,301,1,-1,"4 way valve (Y1S)"},
//{0xA0,12,300,1,-1,"52C Output"},
//{0xA0,13,303,1,-1,"Discharge Temp. Drop"},
//{0xA0,13,302,1,-1,"During emergency operation"},
//{0xA0,13,301,1,-1,"Indoor unit blowout 50 ° C flag"},
//{0xA0,13,300,1,-1,"Powerful bit (MT setting bit)"},
{0xA0,14,105,2,1,"Compressor port temperature"},
{0xA1,0,119,2,1,"(Raw data)Water heat exchanger inlet temp."},
{0xA1,2,119,2,1,"(Raw data)Water heat exchanger outlet temp."},
//{0xA1,4,302,1,-1,"Liquid INJ solenoid valve (Y4S)"},
{0xA1,4,301,1,-1,"Bottom Plate Heater"},
{0xA1,4,300,1,-1,"PHE Heater"},
//{0xA1,5,114,2,1,"Target Discharge Temp."},
//{0xA1,7,114,2,1,"Target port temperature"},
{0xA1,9,305,1,-1,"Monobloc setting"},
//{0xA1,9,304,1,-1,"Minichiller setting"},
//{0xA1,9,303,1,-1,"MT setting"},
//{0xA1,9,302,1,-1,"GSHP setting"},
//{0xA1,9,301,1,-1,"Hydro split setting"},
//{0xA1,9,300,1,-1,"Alterma LT setting"},
//{0x60,0,304,1,-1,"Data Enable/Disable"},
//{0x60,1,152,1,-1,"Indoor Unit Address"},
//{0x60,2,315,1,-1,"I/U operation mode"},
{0x60,2,303,1,-1,"Thermostat ON/OFF"},
{0x60,2,302,1,-1,"Freeze Protection"},
{0x60,2,301,1,-1,"Silent Mode"},
{0x60,2,300,1,-1,"Freeze Protection for water piping"},
{0x60,3,204,1,-1,"Error Code"},
{0x60,4,152,1,-1,"Error detailed code"},
{0x60,5,203,1,-1,"Error type"},
{0x60,6,219,1,-1,"I/U capacity code"},
{0x60,7,105,2,1,"DHW setpoint"},
{0x60,9,105,2,1,"LW setpoint (main)"},
//{0x60,11,307,1,-1,"Water flow switch"},
//{0x60,11,306,1,-1,"Thermal protector (Q1L) BUH"},
//{0x60,11,305,1,-1,"Thermal protector BSH"},
{0x60,11,304,1,-1,"Benefit kWh rate power supply"},
//{0x60,11,303,1,-1,"Solar input"},
//{0x60,11,302,1,-1,"Not in use"},
//{0x60,11,301,1,-1,"Not in use"},
//{0x60,11,300,1,-1,"Bivalent Operation"},
//{0x60,12,307,1,-1,"2way valve(On:Heat_Off:Cool)"},
{0x60,12,306,1,-1,"3way valve(On:DHW_Off:Space)"},
//{0x60,12,305,1,-1,"BSH"},
//{0x60,12,304,1,-1,"BUH Step1"},
//{0x60,12,303,1,-1,"BUH Step2"},
//{0x60,12,302,1,-1,"Floor loop shut off valve"},
{0x60,12,301,1,-1,"Water pump operation"},
//{0x60,12,300,1,-1,"Solar pump operation"},
//{0x60,13,152,1,-1,"Indoor Option Code"},
//{0x60,15,215,1,-1,"I/U Software ID (xx)"},
//{0x60,14,215,1,-1,"I/U Software ID (yy)"},
//{0x60,16,152,1,-1,"I/U EEPROM Ver."},
//{0x61,0,307,1,-1,"Data Enable/Disable"},
//{0x61,1,152,1,-1,"Indoor Unit Address"},
{0x61,2,105,2,1,"Leaving water temp. before BUH (R1T)"},
{0x61,4,105,2,1,"Leaving water temp. after BUH (R2T)"},
{0x61,6,105,2,1,"Refrig. Temp. liquid side (R3T)"},
{0x61,8,105,2,1,"Inlet water temp.(R4T)"},
{0x61,10,105,2,1,"DHW tank temp. (R5T)"},
{0x61,12,105,2,1,"Indoor ambient temp. (R1T)"},
{0x61,14,105,2,1,"Ext. indoor ambient sensor (R6T)"},
//{0x62,0,307,1,-1,"Data Enable/Disable"},
//{0x62,1,152,1,-1,"Indoor Unit Address"},
{0x62,2,307,1,-1,"Reheat ON/OFF"},
//{0x62,2,306,1,-1,"Storage eco ON/OFF"},
//{0x62,2,305,1,-1,"Storage comfort ON/OFF"},
//{0x62,2,304,1,-1,"Powerful DHW Operation. ON/OFF"},
{0x62,2,303,1,-1,"Space heating Operation ON/OFF"},
//{0x62,2,302,1,-1,"System OFF (ON:System off)"},
//{0x62,2,301,1,-1,"Not in use"},
//{0x62,2,300,1,-1,"Emergency (indoor) active/not active"},
{0x62,3,105,2,1,"LW setpoint (add)"},
{0x62,5,105,2,1,"RT setpoint"},
//{0x62,7,307,1,-1,"Add. Ext. RT Input Cool."},
//{0x62,7,306,1,-1,"Add. Ext. RT Input Heat."},
//{0x62,7,305,1,-1,"Main RT Cooling"},
{0x62,7,304,1,-1,"Main RT Heating"},
{0x62,7,303,1,-1,"Pwr consumption limit 4"},
{0x62,7,302,1,-1,"Pwr consumption limit 3"},
{0x62,7,301,1,-1,"Pwr consumption limit 2"},
{0x62,7,300,1,-1,"Pwr consumption limit 1"},
//{0x62,8,307,1,-1,"None"},
//{0x62,8,306,1,-1,"Not in use"},
//{0x62,8,305,1,-1,"Not in use"},
{0x62,8,304,1,-1,"PHE Heater"},
//{0x62,8,303,1,-1,"Tank preheat ON/OFF"},
{0x62,8,302,1,-1,"Circulation pump operation"},
{0x62,8,301,1,-1,"Alarm output"},
{0x62,8,300,1,-1,"Space H Operation output"},
{0x62,9,105,2,-1,"Flow sensor (l/min)"},
{0x62,11,105,1,2,"Water pressure"},
{0x62,12,152,1,-1,"Water pump signal (0:max-100:stop)"},
//{0x62,13,152,1,-1,"[Future] 3 way Valve Mixing 1"},
//{0x62,14,152,1,-1,"[Future] 3 way Valve Mixing 2"},
{0x62,15,105,2,2,"Refrigerant pressure sensor"},
//{0x63,0,307,1,-1,"Data Enable/Disable"},
//{0x63,1,152,1,-1,"Indoor Unit Address"},
//{0x63,2,215,1,-1,"I/U EEPROM (3rd digit)"},
//{0x63,3,215,1,-1,"I/U EEPROM (4th 5th digit)"},
//{0x63,4,215,1,-1,"I/U EEPROM (6th 7th digit)"},
//{0x63,5,215,1,-1,"I/U EEPROM (8th 9th digit)"},
//{0x63,6,215,1,-1,"I/U EEPROM (11th digit)"},
//{0x63,7,215,1,-1,"I/U EEPROM (12th digit)(rev.)"},
//{0x63,8,215,1,-1,"Not in use"},
//{0x63,9,215,1,-1,"Not in use"},
//{0x63,10,215,1,-1,"Not in use"},
//{0x63,11,215,1,-1,"Not in use"},
//{0x63,12,215,1,-1,"Not in use"},
//{0x63,13,311,1,-1,"BUH output capacity"},
{0x63,14,161,1,-1,"Current measured by CT sensor of L1"},
{0x63,15,161,1,-1,"Current measured by CT sensor of L2"},
//{0x63,16,307,1,-1,"HP Forced FG"},
{0x63,16,161,1,-1,"Current measured by CT sensor of L3"},
//{0x64,0,307,1,-1,"Data Enable/Disable"},
//{0x64,1,152,1,-1,"Indoor Unit Address"},
//{0x64,2,316,1,-1,"Hybrid Op. Mode"},
//{0x64,2,303,1,-1,"Boiler Operation Demand"},
//{0x64,2,302,1,-1,"Boiler DHW Demand"},
//{0x64,2,301,1,-1,"Bypass Valve Output"},
{0x64,3,105,2,-1,"BE_COP"},
//{0x64,5,105,2,1,"Hybrid Heating Target Temp."},
//{0x64,7,105,2,1,"Boiler Heating Target Temp."},
{0x64,9,302,1,-1,"Add pump"},
{0x64,9,301,1,-1,"Main pump"},
//{0x64,10,105,2,1,"Mixed water temp."},
//{0x64,12,105,2,1,"2nd Domestic hot water temperature"},
{0x64,14,152,1,1,"Target delta T heating"},
//{0x64,15,152,1,1,"Target delta T cooling"},
};