-------------------------------------------------------------
emonPi_discrete_jeelib Firmware Upload
-------------------------------------------------------------
Downloading firmware from: 
https://github.com/openenergymonitor/emonpi/releases/download/2.9.3/firmware.hex

Downloaded file: 
-rw-r--r-- 1 pi pi 53K Dec  7  2021 /opt/openenergymonitor/data/firmware/emonPi_discrete_jeelib.hex

EmonHub is running, stopping EmonHub

Uploading emonPi_discrete_jeelib on serial port ttyAMA0
Attempt 1...


avrdude-original: Version 6.3-20171130
                  Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
                  Copyright (c) 2007-2014 Joerg Wunsch

                  System wide configuration file is "/etc/avrdude.conf"
                  User configuration file is "/root/.avrduderc"
                  User configuration file does not exist or is not a regular file, skipping

                  Using Port                    : /dev/ttyAMA0
                  Using Programmer              : arduino
                  Overriding Baud Rate          : 115200
avrdude-original: Using autoreset DTR on GPIO Pin 7
avrdude-original: stk500_getsync() attempt 1 of 10: not in sync: resp=0x1c
avrdude-original: stk500_getsync() attempt 2 of 10: not in sync: resp=0xe0
avrdude-original: stk500_getsync() attempt 3 of 10: not in sync: resp=0x1c
avrdude-original: stk500_getsync() attempt 4 of 10: not in sync: resp=0xfc
avrdude-original: stk500_getsync() attempt 5 of 10: not in sync: resp=0x7e
avrdude-original: stk500_getsync() attempt 6 of 10: not in sync: resp=0xc7
avrdude-original: stk500_getsync() attempt 7 of 10: not in sync: resp=0xfc
avrdude-original: stk500_getsync() attempt 8 of 10: not in sync: resp=0x0e
avrdude-original: stk500_getsync() attempt 9 of 10: not in sync: resp=0xff
avrdude-original: stk500_getsync() attempt 10 of 10: not in sync: resp=0xfc

avrdude-original done.  Thank you.

strace: |autoreset: Broken pipe
ERROR: Not in sync
Attempt 2...


avrdude-original: Version 6.3-20171130
                  Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
                  Copyright (c) 2007-2014 Joerg Wunsch

                  System wide configuration file is "/etc/avrdude.conf"
                  User configuration file is "/root/.avrduderc"
                  User configuration file does not exist or is not a regular file, skipping

                  Using Port                    : /dev/ttyAMA0
                  Using Programmer              : arduino
                  Overriding Baud Rate          : 115200
avrdude-original: Using autoreset DTR on GPIO Pin 7
                  AVR Part                      : ATmega328P
                  Chip Erase delay              : 9000 us
                  PAGEL                         : PD7
                  BS2                           : PC2
                  RESET disposition             : dedicated
                  RETRY pulse                   : SCK
                  serial program mode           : yes
                  parallel program mode         : yes
                  Timeout                       : 200
                  StabDelay                     : 100
                  CmdexeDelay                   : 25
                  SyncLoops                     : 32
                  ByteDelay                     : 0
                  PollIndex                     : 3
                  PollValue                     : 0x53
                  Memory Detail                 :

                                           Block Poll               Page                       Polled
                    Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
                    ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
                    eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff
                    flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
                    lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
                    hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
                    efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
                    lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
                    calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
                    signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

                  Programmer Type : Arduino
                  Description     : Arduino
                  Hardware Version: 3
                  Firmware Version: 4.4
                  Vtarget         : 0.3 V
                  Varef           : 0.3 V
                  Oscillator      : 28.800 kHz
                  SCK period      : 3.3 us

avrdude-original: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude-original: Device signature = 0x1e950f (probably m328p)
avrdude-original: NOTE: "flash" memory has been specified, an erase cycle will be performed
                  To disable this feature, specify the -D option.
avrdude-original: erasing chip
avrdude-original: reading input file "/opt/openenergymonitor/data/firmware/emonPi_discrete_jeelib.hex"
avrdude-original: input file /opt/openenergymonitor/data/firmware/emonPi_discrete_jeelib.hex auto detected as Intel Hex
avrdude-original: writing flash (19260 bytes):

Writing | ################################################## | 100% 2.72s

avrdude-original: 19260 bytes of flash written
avrdude-original: verifying flash memory against /opt/openenergymonitor/data/firmware/emonPi_discrete_jeelib.hex:
avrdude-original: load data flash data from input file /opt/openenergymonitor/data/firmware/emonPi_discrete_jeelib.hex:
avrdude-original: input file /opt/openenergymonitor/data/firmware/emonPi_discrete_jeelib.hex auto detected as Intel Hex
avrdude-original: input file /opt/openenergymonitor/data/firmware/emonPi_discrete_jeelib.hex contains 19260 bytes
avrdude-original: reading on-chip flash data:

Reading | ################################################## | 100% 2.03s

avrdude-original: verifying ...
avrdude-original: 19260 bytes of flash verified
strace: |autoreset: Broken pipe
strace: |autoreset: Broken pipe
strace: |autoreset: Broken pipe
strace: |autoreset: Broken pipe
strace: |autoreset: Broken pipe

avrdude-original done.  Thank you.

strace: |autoreset: Broken pipe
SUCCESS: flash verifed

Restarting EmonHub